Page 1694 – RTO Insider

April 23, 2013

Cost Recovery Criteria OK’d

The Commission approved criteria for determining which NERC activities are eligible for cost recovery under section 215 of the Federal Power Act.

Reason for change:

A FERC audit issued last year recommended the development of the criteria.

Impact:

The criteria restrict funding to “statutory” activities such as those involving the development, monitoring and enforcement of reliability standards, along with related training.

FERC will use the criteria in approving NERC’s annual budgets. Expenses approved by FERC are eligible for cost recovery from end users.

The commission ruled that the proposed criteria were generally acceptable but required replacement of the term “involve or support” with the term “necessary or appropriate” as the basis for funding. The commission said the former term was too broad and provided no practical limitation on funding.

April 23, 2013

Cyber Asset Definitions

Programmable electronic devices and communication networks including hardware, software and data.

Bulk Electric System (BES) Cyber Asset

A cyber asset which, if lost, damaged or misused would within 15 minutes affect the reliable operation of the grid. Redundancy of affected facilities is not considered when determining adverse impact. The definition excludes assets connected to the grid for 30 consecutive days or less that are used for data transfer, vulnerability assessments, maintenance, or troubleshooting.

April 23, 2013

FERC OKs New Reliability Standards

Expanded Cybersecurity Focus

New Approach for Generators

WASHINGTON — The Federal Energy Regulatory Commission gave preliminary approval Thursday to a rewrite of cybersecurity rules and set a “bright line” requiring most facilities at 100 kV or higher to abide by them.

The commission issued four orders approving proposals by the North American Electric Reliability Corp. (NERC). Included were:

A new definition of transmission facilities covered by NERC reliability rules that upgrades the longstanding 100 kV threshold from a guideline to a directive. Regional discretion on the definition of Bulk Electric Systems (BES) is eliminated. (more)
Version 5 Critical Infrastructure Protection (CIP) standards, which replace the current “in or out” designations with a tiered approach which classify assets as high, medium or low impact. The commission said version 5’s improvements were important enough that companies now operating under CIP version 3 will skip CIP Version 4, due to take effect date, April 1, 2014, and transition directly to version 5. (more)
New rules for generator interconnections that will eliminate the need for most generators to register as transmission operators. (more)
Criteria for determining which NERC activities are eligible for cost recovery. (more)

April 23, 2013

New Reliability Rules for Generator Interconnections

The commission issued a Notice of Proposed Rulemaking for four new reliability standards addressing vegetation management and facility connection requirements for generator interconnection facilities (also known as generator tie lines).

Reason for Changes:

FERC had encouraged NERC to identify reliability standards specific to generator owners and operators with interconnection facilities including transmission lines. Eliminating the need for generators to register under the transmission function will allow them to focus on reliability standards specific to them, NERC said.

Impact:

FAC-001-1 requires a Generator Owner to publish facility connection requirements when it executes an agreement to evaluate the reliability impact of interconnecting a third party facility to its tie line.
FAC-003-3 requires a Generator Owner to perform vegetation management on its tie line.

Standards PRC-004-2.1a (Analysis and Mitigation of Transmission and Generation Protection System Misoperations) and PRC-005-1.1b (Transmission and Generation Protection System Maintenance and Testing) establish generation owners’ responsibility for the FAC requirements as they apply to tie lines.

In most cases, NERC said, these are the only reliability standards that apply to generator interconnection facilities. The changes do not affect the requirement that generators comply with other reliability standards unrelated to tie lines, such as those covering system restoration plans and notification of equipment failures.

Generators currently registered under transmission functions will have to apply to change their certifications under the NERC Rules of Procedure.

April 23, 2013

MRC Preview: Black Start Compensation; DR “Fatigue;” UTCs; CFTC Response on Agenda

Below is a summary of the issues scheduled to be brought to a vote at Thursday’s Markets and Reliability Committee meeting. Each item is listed by agenda number, description and projected time of discussion, followed by a summary of the issue and links to prior coverage in PJM Insider.

Rich Heidorn will be in Wilmington covering the votes. Sign up for his Twitter feed to get real-time alerts on when these issues come up for discussion, and see next week’s newsletter for a full report.

2. PJM MANUALS (9:10-9:20)

The committee will be asked for endorsements of changes to Manual 13: Emergency Operations related to the integration of East Kentucky Power Cooperative.

East Kentucky Coop to Join PJM

Tariff Changes OK’d for East Kentucky Integration

3. SYSTEM RESTORATION STRATEGY SENIOR TASK FORCE (SRSTF) (9:20-9:50)

Transmission operators providing cranking paths for black start generators would recover capital costs over five years under a proposal by the System Restoration Strategy Task Force that the MRC will be asked to approve. The task force rejected an alternate proposal that would have extended capital recovery over the entire asset life.

MRC First Readings: Capital Cost Recovery for Black Start Generators

MRC will be asked to approve on first read a revised charter that will expand the scope of the task force’s work. The revised charter would include consideration of “back stop options.”

4. PROVISION OF E-TAG DATA TO ISOS, MMUS, AND FERC (9:50-10:00)

PJM needs to make revisions to the confidentiality provisions of its tariff to comply with FERC Order 771, requiring provision of E-Tag data to Independent System Operators, Market Monitoring Units and FERC.

MRC First Readings: Provision of E-Tag Data

5. FREQUENCY CAPABILITY VERIFICATION (10:00-10:15)

Ken Carretta, of PSEG, will ask the MRC to endorse a problem statement exploring whether PJM has sufficient safeguards to ensure that Emergency Demand Response resources perform as needed.

PJM expects DR to be called on increasingly in the future due to declining installed generation reserve margins. That has led to concern by some that performance may suffer as a result of DR “fatigue.”

At MRC’s March 28 meeting, curtailment service providers said that there was no evidence of “fatigue” and alleged the proposal was anticompetitive. Carretta said reporting requirements that could result from the inquiry would be no more onerous than those for generators.

Cool Reception for DR “Fatigue” Study

Demand Response Calls Expected to Grow in 2014

6. UP-TO CONGESTION TRANSACTION ENHANCEMENT (10:15-10:40)

PJM delayed a vote on its proposal to limit Up-to Congestion (UTC) bids Feb. 28 when MRC members asked for a broader review to come up with a consensus definition of the bidding technique.

PJM is proposing the cap because high bid volumes can make it difficult for the RTO’s day ahead markets software to reach solutions. Although the proposal was supported by financial market players who are the predominant users of UTC, other members balked, calling for a broader review of the impact of UTCs, which have grown in popularity since their creation in 2000.

MRC will be asked to approve bid limits similar to those that apply to increment offers and decrement bids for inclusion in Manual 11. The proposed revisions also add the following definition of Up-To Congestion transactions to the OA and Tariff:

“A Market Participant may elect to submit in the Day-ahead Energy Market a form of Virtual Transaction that combines an offer to sell energy at a source, with a bid to buy the same megawatt quantity of energy at a sink where such transaction specifies the maximum difference between the Locational Marginal Prices at the source and sink. The Office of Interconnection will schedule these transactions only to the extent this difference in Locational Marginal Prices is within the maximum amount specified by the Market Participant.”

Facing Opposition, PJM Delays UTC Cap Pending Broader Review

7. APPLICATION OF FTR FORFEITURE RULES TO UP-TO CONGESTION TRANSACTIONS (10:40-11:00)

PJM will ask MRC approval to apply FTR forfeiture rules to Up-to Congestion transactions. The action will require changes to the OA, Tariff and PJM Manual 6: Financial Transmission Rights.

The rules are intended to prevent market participants from submitting virtual bids that boost the value of their FTRs.

On March 28, the MRC rejected PJM’s proposed tariff changes specifying how the FTR forfeiture rules are applied to increment offers and decrement bids.

PJM, Monitor in Stalemate on FTR Forfeiture Rule

8. COMMODITY FUTURES TRADING COMMISSION (CFTC) EXEMPTION ORDER (11:00-11:30)

PJM announced April 7 that it may deny trading privileges to as many as 55 small market participants if they are unable to qualify for the Dodd-Frank exemption approved by the Commodity Futures Trading Commission last month.

MRC will be asked to approve changes to the Operating Agreement and Tariff to comply with conditions in the CFTC order and to implement PJM’s response to it.

CFTC Approves Dodd-Frank Exemption for RTOs

PJM May Bar Some Financial Players from Trading; 55 Companies Affected by Response to CFTC Order

April 18, 2013February 25, 2024

FERC Stands Firm on Reporting Requirements – UPDATE

By Rich Heidorn Jr.
PJM Insider

WASHINGTON – Large electric cooperatives and public power agencies must begin reporting their “surplus” power trades to the Federal Energy Regulatory Commission, the agency said today, standing firm on an order it issued in September.

The new reporting requirements apply to more than 50 cooperatives and public power agencies otherwise exempt from FERC authority that have “more than a de minimis market presence” – defined as more than 4 million MWh in annual wholesale sales.

The newly-affected entities must begin recording their transactions in Electric Quarterly Reports (EQRs) for the third quarter of 2013.

In denying a request for reconsideration, the commission also reiterated its requirement that all EQR filers begin including electronic tag (e-Tag) data in reporting their transactions.

Reason for change:

Order 768, issued Sept. 21, is a response to Congress’ command in the 2005 Energy Policy Act to improve price transparency in wholesale electric markets.

The commission said the reporting requirements were necessary because non-public utilities are responsible for about 29% of wholesale sales in the 48 contiguous states (excluding ERCOT). They represent 60% or more of sales within the Western Electric Coordinating Council (WECC), SERC Reliability Corp. and Florida Reliability Coordinating Council (FRCC) FERC said.

The American Public Power Association said the commission’s estimate overstates the role of non-public utilities, which it estimated at 19% of sales nationally. APPA said the data FERC used, from the Energy Information Administration’s (EIA’s) Form 861, are inaccurate because EIA reports a power marketer’s sales as being from a single region although it may make sales in several regions.

Impact:

The reporting requirements cover only “surplus” sales. Excluded from reporting are cooperative and joint agency sales to members or long-term, cost-based sales required by state or federal law.

The order may affect more than 40 public power utilities whose sales top 4 million MWh, according to data compiled by the American Public Power Association. Among the largest agencies are several PJM members, including American Municipal Power, Inc., North Carolina Municipal Power Agency No. 1, Indiana Municipal Power Agency and WPPI Energy. (To help PJM market participants in their data gathering, the Market Settlements Reporting System (MSRS) provides reports formatted to match the EQR structure.)

About half of the 60 largest generation and transmission cooperatives also are likely to be covered by the new rule, according to a former FERC staff attorney who had analyzed the order’s impact.

FERC estimated in Order 768 that the rule would cover about 53 non-public utilities above the threshold.

The order also added new fields in the EQR for:

reporting the trade date and the type of rate;
identifying the exchange used for a sales transaction, if applicable;
reporting whether a broker was involved; and
reporting electronic tag (e-Tag) ID data.

It also standardized reporting of prices and quantities for energy, capacity and booked out transactions and requires entities to disclose whether they report their sales transactions to an index publisher.

The Commission did cut two requirements, eliminating reporting on time zones and Data Universal Numbering System (DUNS) information.

Industry Reaction:

The National Rural Electric Cooperative Association said that FERC overestimated the impact of its members on wholesale markets and that the EQR expansion would not improve transparency.

However, the Pennsylvania Public Utility Commission supported the reporting requirement, saying it will help its ability to monitor retail markets for anti-competitive behavior. Pennsylvania has 13 rural electric cooperatives and about 35 municipal electric utilities.

Market monitors for PJM, MISO, NYISO, ISO-NE SPP, and California ISO also supported the requirement. The monitors noted that the commission’s market-based rate program is based on “regulation through competition,” and is thus dependent on mitigating market power.

FERC contacts:

Maria Vouras, Office of Enforcement, (202) 502-8062, Maria.Vouras@ferc.gov
Christina Switzer, Office of the General Counsel, (202) 502-6379, Christina.Switzer@ferc.gov

April 16, 2013

PJM to Alter Practice on Billing Transfers

In response to recent bankruptcy court rulings, PJM will no longer incorporate billing line item transfers when calculating member credit requirements, RTO officials told the Market Implementation Committee last week.

A billing line item transfer allows a member to partially offset its accounts payable with a receivable owed them by another member. The netting of charges from these counterparty transactions are reflected in PJM’s invoices: one invoice increases by the same amount as the second decreases.

Reason for Change: Because PJM uses net invoice values in determining credit requirements, the practice can create a “three-party setoff” between PJM and the two members involved in the transfer. Recent bankruptcy court rulings have restricted the allowance of three-party setoffs, meaning PJM might be precluded from seizing assets in the event of a member bankruptcy.

Impact: PJM will continue to allow line item transfers but will exclude the netting from credit calculations in cases that could increase the RTO’s credit exposure. The change will be effective late in the second quarter. Recalculation of credit requirements will be prospective only.

PJM contact: Hal Loomis

April 16, 2013

Demand Response Calls Expected to Grow in 2014

PJM expects to call on its demand response resources from five to nine times per year starting in the 2014/15 delivery year, up from an expected one to five calls in 2013/14.

The projection reflects the increasing volume of DR clearing in PJM capacity auctions and the impact of plant retirements, which are expected to reduce the Installed Generation Reserve Margin (IGRM) to 9% in 2014 from the current 13%.

PJM briefed the Planning and Market Implementation committees last week on the projections, the results of a GE-MARS Monte Carlo loss of load probability model. The simulations used 2002 data for a “typical” load shape (the same year used in the recent NERC Probabilistic Assessment report).

Likely DR calls are highest in Southwest MAAC and lowest in the Dominion zone (see previous chart).

Scenario analyses showed the results were highly dependent on the amount of generation reserves assumed, that is, whether uncleared internal generation will be available to serve PJM load. Assumed emergency import capabilities, particularly into SWMAAC, also had a significant impact. The results were not affected much by the assumed DR triggers.

Since the 2010/11 delivery year (June 1 – May 31), PJM has declared 11 Emergency DR events, resulting in nine Energy Emergency Alert (EEA) 2s. EEA2s, called to implement load management procedures, are posted on the Reliability Coordinator Information System (RCIS) and on the PJM Emergency Procedures site.

April 16, 2013

Transmission System Briefs

In an effort to improve data collection, PJM will soon begin testing a new method for making interconnection applications.

Reason for Change: PJM engineers have to request additional information on half of the applications made using the current method.

Impact: The new method will use a question-and-answer process to guide applicants. PJM will be seeking a half-dozen volunteers to test the system in June and July before it is deployed. Those interested in volunteering should contact PJM through RTEP@PJM.com.

New Network Protocol for Small Generators

Small generators using public-domain Internet for access to PJM’s SCADA system will be switching to a new system intended to improve security and reliability.

The change affects load response and renewable generation assets under 100 MW not ‘sponsored’ by a generation company, aggregator or marketer.

The current system employs asymmetric “Shared Secret” encryption and uses the public-domain Internet. The new system, which uses “Public Key” encryption based on open standards, is favored by auditors and is considered close to industry best practice, PJM said.

The transition will take three to four years.

PJM contact: Ryan Nice

Dominion Adding Four New 500 kV Line Designations

Dominion’s interconnection of the Brunswick Power Station, a 1,551 MW combined cycle plant, will result in the creation of four new 500 kV line designations.

Dominion is building two new 500kV substations at Rawlings and Brunswick which will require the split of the two existing 500 kV lines: 511 Clover – Carson and 570 Wake – Carson. The two will be split into four lines: 511 Carson – Rawlings; 585 Carson – Brunswick; 591 Brunswick – Rawlings, a new 14-mile line; and 509 Brunswick – Brunswick Power Station, a new one-mile line. The work is targeted for completion in 2016.

FirstEnergy Shutting Reading Control Center

FirstEnergy will shut down its Reading, Pa., transmission control center and move operations to its Wadsworth, Ohio, center on April 29th. The phone numbers will remain the same.

The Wadsworth facility will itself be replaced by a $45 million control center planned for FirstEnergy’s West Akron campus. The new facility is expected to be complete by the end of 2013. It will oversee transmission operations for all of FirstEnergy’s utilities excluding Mon Power, Potomac Edison and West Penn Power, which will continue to be run from the company’s Fairmont, W. Va., center. The Wadsworth location will be used as a back-up and training facility.

Revised Transmission Matrix Approved

The Operating Committee last week approved revisions to the Transmission Owner/Transmission Operator matrix, an index between NERC reliability standards and PJM manuals.

Reason for change: The matrix is used as a tool during TO/TOP audits. The changes incorporate standards becoming effective this year.

Impact: The changes go next to the Transmission Owner Agreement Administrative Committee for approval.

PJM contact: Mark Kuras

Transient Security Assessment Coming to Real-Time Ops

PJM has begun testing Transient Security Assessments in real-time operations in preparation for a scheduled for June 1 deployment.

Reason for Change: The tool will monitor the transient stability of the PJM system and compute stability limits through real-time data input and network models. The system will collect data every 15 to 20 minutes, allowing PJM operators to implement controls to prevent generators from becoming unstable. PJM has been using the tool in near-term outage studies since the end of 2012.

Impact: Operators will switch from using stability limits found in Manual 3 to those coming from the TSA. PJM’s Dave Souder said the new tool should be more accurate because it is based on real-time conditions as opposed to the light load, conservative case, in Manual 3. The market impact should be “very minor,” said PJM’s Liem Hoang.

The deployment will require completion of benchmarking with ComEd and AEP, updates to Manual 3 and 3A and additional training for PJM operators. Immediately after deployment, operators will monitor only known stability concerns identified in M-03.

PJM contacts: Jianzhong Tong (tongji@pjm.com), Liem Hoang (hoangl@pjm.com)

Removal of Edison Mission Energy SPS in ComEd Zone

A Special Protection System activated to allow an Edison Mission Energy merchant interconnection in the ComEd zone (V3-052 and W2-038) will be removed on August 15. The SPS was used regularly and was still providing congestion relief after the completion of the required upgrades. Economic upgrades for the area have not passed PJM’s cost-benefit screens.

Baltimore Gas & Electric Activating SPS

Baltimore Gas & Electric will activate a Special Protection System for its Concord Street and Mount Washington 115kV lines on June 1 to allow for baseline system upgrades. The Concord Street SPS, designed to alleviate thermal overloads, will be removed with the completion of baseline upgrade b1086, expected in June 2014. The Mt. Washington SPS, intended to correct voltage drop violations, will be removed on the completion of baseline upgrades b1267 and b1267.1 in about June 2018.

April 16, 2013

EPA Delays GHG Limits for New Generators

The Environmental Protection Agency has delayed indefinitely its proposed greenhouse gas limits on new power plants.

EPA last year proposed a rule that would bar new generators from emitting more than 1,000 pounds of carbon dioxide per megawatt hour of electricity production.

An EPA spokeswoman told The Washington Post Friday that the agency could not complete review of the more than 2 million comments in time for an April 13 deadline for finalizing the rule. The spokeswoman said no new timetable had been set.

The Post reported that EPA is considering changes to improve the regulation’s chances of surviving a legal challenge. Read more in the Post.